Patio Door Lock Repairs

Over time, the wear and tear can cause lock malfunctions. Fortunately, there are several simple and effective ways to restore your uPVC patio door's security.

These easy fixes will ensure your home is secure, whether you realign the lock or clean the locking mechanism.

Clean the Lock

Patio doors are fantastic for bringing the outdoors inside and keeping out the elements. However, they can be a security threat in the event that the lock isn't working correctly. Over time wear and tear cold and hot weather dirt and debris can take their toll on the lock of your patio door and make it difficult to open. With a little attention, you can make sure that your lock for your patio screen door repair door is always working properly.

It's important to first clean the patio door lock as well as all moving parts. This helps flush out any accumulated grime and coatings that could be preventing the lock from working in the way it should. Start by wiping the moving parts on the lock for your patio door with a wet cloth. Then, use a scouring cloth or rough damp cloth to scrub the areas that are soiled of the frame and door. It is recommended to wipe the entire lock with dry cloths to eliminate any remaining dampness, and allow it to air dry before making use of it again.

If your patio door has pin-tumbler latches You can apply powdered Graphite to the key. You can also apply a Teflon lubricant like WD-40 Multi Use Product. This kind of lubricant is easy to apply, and doesn't break down over time. If you're unable to locate the right lubricant for your needs you might try using a pencil with a thick tip. Put the pencil into the lock and jiggle it around to distribute the graphite.

Regular maintenance is also necessary to keep the tracks of sliding patio doors free of dust, dirt and other debris. These tracks are especially susceptible to ice, snow, and other debris that could cause them to block or become stuck. This could make it difficult for your patio door to open and close.

The sliding patio door repair service near me rails of the patio door track and rollers can be cleaned by removing dirty or damaged weather stripping and then cleaning it, before installing it. The same is true for rollers on patio doors, which can be cleaned and then sprayed with a non-stick lubricant to help them move freely.

Lubricate the moving parts

uPVC French Doors, like sliding patios, are operated with 3 to 4 or sometimes, 5 point locking mechanisms. This includes the handle and lock cylinder that is operated with keys. These doors also need maintenance, and specifically lubrication of the moving parts. This can be done with a thin oil, but never WD40. It should be done at least once per year.

If sagging hinges aren't a reason, the door could be skewed and catch or rubbing against the strike plate's hole in the frame. Take off the strike plate and employ a sharp tool enlarge the mortise. This will permit the latch to fit properly into the hole, and stop it from scratching against the frame.

When the cylinder is out of the way and out of the way, measure its width using the help of a book or piece wood that can fit into the adjustment screw gap above the lock. The outer dimension is the distance from the outside of the door to the center of the cylinder, while the inner measurement runs from the center of the adjustment screw to the end of the cylinder.

Check the width of the lock.

If your patio door lock repair door latch isn't able to turn even after oiling and cleaning it could be because it's not aligned properly with the strike plate. Verify that the door is in a balanced position, and that the hinge screws are in good condition. In most cases, moving the strike plate upwards or downwards will solve the issue.

The latch may not be able to engage properly when the strike of the lock is not large enough. In this situation, you'll need to enlarge the opening using the hammer or chisel and then test the latch to ensure that it contacts the strike plate in a smooth manner without rubbing against or landing on the frame of the door jamb.

Before you purchase a replacement lock, you should first identify the type of mortise lock you have. This can be done by looking at the end faceplate and noting whether it is round or square. Look at each screw hole in the existing lock and note their dimensions. This will help you to locate a replacement lock that is exactly the same width and will fit in the hole you have already.

In addition to identifying the mortise lock that is currently in use, you'll also want to inspect it for any bends or scratches that might require repair. A damaged or bent latch is more likely than one that has been used a lot to break. Replace the lock if you notice signs of damage.

After you've examined the lock and identified which type of replacement you'll need then it's time to begin working on the actual repair. Remove the handle and spindle out of your patio door, and then install the new one. Begin by installing the interior handle. Align it with the spindle, and then secure it into by using two bolts or screws. Install the exterior handle following the interior handle. Once you have completed these steps check the handles to make sure that they open and shut easily and that the latch is in contact correctly with the strikeplate.

Check the Strike on the door.

The door latch and strike plate are the two parts of the lock that work together to ensure that the latch locks the door. If they are not aligned properly and the latch isn't latching the door shut properly. Fortunately, the issue is usually simple to fix.

Check the receiving holes of the strike plate to make sure they are free of obstructions like dirt or plastic plugs. Then loosen the keeper screws that keep the strike plate in place and allow it to move horizontally, but not removing it from the frame of your door. Adjust the strike plate so that it aligns its holes for receiving with latch hooks of the door latch. After the strike plate has been adjusted then tighten the screws and test the door to see whether it shuts easily with the new adjustment.

These plates are difficult to reach for homeowners who have sliding patio doors. However they are vital for locking and unlocking your door. The plates made of metal are located between the top and bottom jambs of the door, where they support its latch. The door latch slides into the strike plate to create an airtight seal when closed. If the strike plate has been damaged or rusted, or if it is not installed correctly the latch may not be able to lock the door properly.

One of the most common reasons for a patio door lock to become stuck or not close is a misalignment of the latch and strike plate. This can be checked with the "lipstick" test. Apply a little lipstick across the edge of the deadbolt. Then cover it with masking tape. When you close the door the lipstick will leave a mark on the tape that will show exactly where the latch meets the strike plate. If the mark is too low or high you can easily alter the strike plate.

sliding patio doors repairs patio screen door repair near me door locks help protect your home from intruders, and if they're not working properly, you need to solve the issue fast. Follow these easy steps to fix your patio door lock and restore it's functionality.