Patio Door Lock Repairs

Over time, patio doors experience wear and tear that could cause lock malfunctions. Fortunately, there are several easy and efficient methods that can restore your uPVC patio door's security.

These simple fixes can make your home safer no matter if you adjust the lock or clean the locking mechanism.

Clean the Lock

Patio doors are fantastic for letting the outdoors in and keeping out the elements. However they could pose an issue for security when the lock isn't functioning properly. With time, wear and tear, extreme cold and hot weather, dirt and debris can cause damage to the lock on your patio door and make it difficult to open. Fortunately, with a little care, you can ensure the locks on your patio door repair service door always perform properly.

It's important to first clean the patio door lock and all moving parts. This will help get rid of any grime and coatings that may hinder the lock from functioning as it should. Begin by wiping down the moving parts of the lock for your patio door with a damp, clean cloth. then employ a scouring pad or rough damp cloth to scrub the hard-to-reach areas of the door and frame that are ingrained with dirt. You should then wipe down the entire lock using dry cloth to get rid of any remaining dampness and let it to air dry before applying it to the next time.

If you have an exterior door that is fitted with pin tumbler latch mechanisms it is possible to lubricate the lock by applying graphite powdered to the key or by using a Teflon-based lubricant such as WD-40 Multi-Use Product. This type of lubricant is easy to apply and it doesn't dissolve over time. If you're unable find the correct lubricant for your lock, you can make use of a pencil with a more of a thicker tip. Put the pencil in the lock, then shake it to distribute the graphite.

Regular maintenance is also essential to keep the tracks of sliding patio doors free of dust, dirt and other debris. These tracks are especially susceptible to snow and ice which can cause them to be stuck or jammed which makes it difficult for your patio doors to open and close.

You can clean the track rails and rollers of sliding patio Door Lock repair doors by removing weather stripping that is dirty or damaged. Clean it, and then replace it. patio glass repair near me door rollers can also be cleaned and sprayed down with an oil that is nonstick.

Lubricate the Moving Parts

uPVC French doors, like sliding patio door repair patios, operate by using 3 to 4 or sometimes 5 point locking mechanisms. They include the lock cylinder and handle which is operated by the key. These doors also need maintenance, including lubrication of the moving parts. This can be accomplished using an oil that is thin (never WD40) and should be done every year.

If the hinges aren't causing the problem, it could be that the door is not aligned. It may be rubbing against or catching the strike plate's opening in the frame. The solution is to take off the strike plate, and then use an abrasive chisel, which will enlarge the mortise that it rests in. This will allow the latch to fit into the hole, and prevent it from scratching against the frame.

When the cylinder is out of the way take a measurement of its width using the help of a book or piece wood that can fit into the gap of adjustment screw above the lock. The outer dimension is measured from the outside of door to the center cylinder. The inner dimension is measured from the center adjustment screw until the end of the cylinder.

Check the lock's length

If your patio door latch isn't able to turn, even after cleaning and oiling it could be because it's not aligned with the strike plate. Verify that the door is balanced and whether the hinge screws are tight, but in many cases shifting the strike plate upwards or downwards can fix the issue.

The latch may not be able to engage properly in the event that the strike of the lock is not large enough. In this case, enlarge the hole with an hammer and chisel. Then, test the latch to ensure that it doesn't rub against the jamb frame of the door or get caught on it.

You should identify the type mortise lock you currently are using before you purchase a replacement. This can be done by looking at the faceplate on the lock and determining whether it is round or square. Then, look at the screw holes on the existing lock and note the dimensions of each one. This will help you to locate a replacement lock that is the exact same width and fits into the hole that you already have.

You'll need to identify the mortise lock and inspect it for bends, scratches or other damage that need to be repaired. A bent or damaged latch is more prone to break than one that's not used much, so be sure to replace the lock with a brand new, secure version in the event you notice any signs of wear or damage.

After you've examined the lock and determined which kind of replacement you require now is the time to start working on the actual repair. The old handle and spindle should be removed from the doorway to the patio. Insert the new handle. Start by putting in the handle inside by aligning it with the spindle, and then fixing it with the two screws or bolts that hold it. Install the exterior handle after the interior handle. Once you have completed these steps, test the handles to make sure they are able to open and close easily and that the latch works correctly with the strikeplate.

Make sure you check the Strike of the door.

The door latch and strike plate are the two components of the lock that work to ensure that the latch is secure the door. If these are misaligned and the latch doesn't latch the door shut correctly. This problem is usually very easy to solve.

Check the holes for receiving of the strike plate to make sure they are clear of obstructions like dirt or plastic plugs. Then loosen the keeper screws that keep the strike plate in place and allow it to move horizontally, but not removing it from the frame of your door. Adjust the strike plate to align its holes for receiving with the latch hooks of the door latch. After the strike plate has been adjusted tighten the screws, and test the door to see whether it shuts easily with the new adjustment.

Door strike plates can be a bit difficult to access for homeowners who have sliding patio doors, however they're essential for locking and unlocking your door. The metal plates are situated at the top and bottom jambs of the door where they serve as the support for the latch. The door latch is placed on the strike plate, creating an airtight seal when closed. If the strike plate is damaged, rusted or not properly installed, it could hinder the latch from locking the door securely.

One of the most common reasons for the patio door repairs near me door lock to become stuck or not close is a misalignment of the latch and the strike plate. The most effective way to test for this is with the "lipstick test." Rub some lipstick on the outside of the deadbolt, and then apply masking tape over it. When you shut the door the lipstick will leave a mark on the tape, showing you exactly where the latch contacts the strike plate. If the mark is too low or high you can easily adjust the strike plate.

If your patio door locks for sliding aren't working correctly, they can keep your home secure from intruders. You need to fix this problem as soon as possible. By following these easy steps, you can fix your patio door repair near me door's lock and get it back to normal in no time.