How to Replace a Kia Sportage Replacement Key

For a number of Kia models the key comes with a built-in keyless entry system. The key functions like an remote control and can be exchanged by an Kia dealer.

Key fobs are prone to malfunction due to a variety of reasons, including an empty coin battery, worn buttons water damage, signal interference, and a defective receiver module. Here are some tips on how you can get your Kia Sportage replacement key to work again.

How do you replace the remote key or smartkey?

It doesn't matter if your kia soul key replacement comes with an intelligent key, remote key push to start key, or a standard non-transponder key made of metal The battery inside these keys will eventually need replacing. This is especially relevant if your vehicle shows a message that states the smart or remote keys are not powered by batteries.

It's a fairly simple process. In order to replace the key fob battery take out the mechanical key from the slit at the back of the key fob. Then lift the cover. Inside the key fob, there will be the small screw that holds the battery in its place. Using a small screwdriver, take the screw off and remove the old battery. Install the new battery and close the opening on the key fob.

Test the key fob by pressing the lock or unlock buttons. It's okay If the doors lock and unlock as expected. You can now use the hands-free feature to lock and unlock your Kia whenever your fingers feel cold or when you need to run errands around Brandon.

Not all key fobs might need to be programmed (transponder chips or smart keys). This requires a specific programming machine that only the dealer or automotive locksmith has access to. Other keys (non transponder metal keys) are not required for programming. If you need to reprogramme your key, you'll need to write down the key code's number on the key code tag.

How to replace a battery

If your Kia key fob isn't responding when you press the lock or unlock button on the fob, this is a clear indication that the battery should be replaced. A battery that is not functioning properly could cause other problems like the check engine light turning on or delayed engine cranking. Fortunately replacing the key fob battery is a simple DIY project that requires just a few tools.

Make sure that you shut off your vehicle and close all doors prior to starting. Find the small metal or plastic piece that is located at the bottom of the key fob. Then, jiggle it until the metal key is released. This key can be placed inside the driver door handle to unlock your car.

To replace the key fob battery, take off the cover on the rear and use a plier bar tool to loosen the latch holding the black negative battery cable. Take the old battery out, and then orient the replacement battery to ensure that its "+" side faces you, and the "-" negative side is facing the fob's electrical contacts. Push the new CR2032 battery straight into place, avoiding excessive force to avoid damaging or bending the contacts made of metal.

Once the new battery is installed, turn the key fob off and on in the ignition for a few times until the door locks cycle. You can then test the Kia's key fob once more to ensure it's working properly.

How do I replace a smart key

There is a possibility of having a standard keyfob or a Smart Key based upon the model of kia rio replacement key fob Sportage. The difference between them is that the smart key has the small blade of a key tucked inside it, while the standard fob does not. Both key fobs are equipped with batteries that will eventually require replacement. This is a straightforward process that takes only two minutes.

Make sure you turn off your Kia and stand on a level, well-lit surface before you begin. Be aware that there are tiny parts inside the fob that can be removed if not vigilant.

The first step is to find the small release button on the backside of the fob. It's either a circular or rectangular slot. When you press it the mechanical key blade will appear and you will be able to open the key fob.

Once you have the key fob opened then you can take off the old battery and replace it. The new battery is CR-2032, and can be bought from a local or online auto parts store. After you've finished, you should be able to lock and unlock your vehicle using your key fob even if the engine isn't running!

How do you replace a broken mechanical key

The Kia key fob is a great feature that lets us lock and unlock our car with the push of one button. Like any other device, the kia ceed key fob replacement key fob can occasionally have problems. There are solutions to address these issues and keep your key fobs in good working order for many years.

A dead or weak battery is one of the most frequent problems. This can cause your fob to stop working or operate intermittently. If this happens try replacing the battery with a new one.

If this doesn't resolve the issue, try using a standard flat-head screwdriver to break open the fob's plastic casing. Be careful not to damage any internal components or scratch the plastic. Once the battery is removed and replaced, you can replace it with a brand new battery.

Close and open the door using the mechanical key. (Every kia fob comes with an emergency mechanical key which will fit into the slot). Test the key fob and ensure that it's working correctly. If the key fob not working, contact an authorized locksmith or dealer to help resolve the problem. Make sure they make you an emergency key that functions for all door and trunk cylinders to avoid lockouts in the future.