Patio Door Lock Repairs

Over time, patio doors undergo wear and tear that could result in locks that fail. Fortunately, there are several simple and effective ways to restore your uPVC patio door's security.

It's about realigning the lock or cleaning the locking mechanism these simple fixes will help you make your home more secure.

Clean the Lock

Patio doors are fantastic for letting the outdoors in while keeping out the elements. However, they can be risky for security if the lock doesn't work properly. As time passes wear and tear cold and hot weather dirt and debris could cause damage to the lock on your patio door and cause it to become difficult to open. With a little attention you can ensure that your lock for your patio door is always working properly.

In the beginning, it's essential to clean your patio door's lock and all of its moving parts. This will help remove any coatings or dirt that could be preventing the lock from working correctly. Begin by wiping down the moving parts of the lock for your patio door using a damp cloth. then make use of a scouring pad, or a rough damp cloth to scrub any hard-to-reach areas of the door and frame that are coated with dirt. Then clean the lock with a dry towel to remove any remaining moisture. Let it air dry before you use it.

If your patio door uses pin-tumbler latches you can apply powdered graphite to the key. You can also apply a Teflon lubricant such as WD-40 Multi Use Product. This type of lubricant can be applied with ease and does not dissolve over time. If you're not able to find a suitable lubricant you could try using a pencil that has an extremely sharp tip. Place the pencil in the lock and jiggle it around to spread the graphite.

Tracks for sliding patio doors repairs patio doors require regular maintenance to ensure that they're free of dirt, dust and other debris. These tracks are especially vulnerable to snow and ice which can cause them jam or bind which makes it difficult for your patio doors to open and close.

Clean the track rails and rollers of sliding patio doors by removing weather stripping that is dirty or damaged. Clean it and replace it. patio sliding door repair near me door rollers can also be cleaned and sprayed down with an oil that is non-stick.

Lubricate the moving parts

uPVC french doors, similar to sliding patio doors, work with 3-4 or sometimes 5-point locking mechanisms which include the lock cylinder and handle operated by keys. They also require maintenance, specifically lubrication on the moving parts. This can be done using a thin oil but not WD40. It is recommended to do it every year, at a minimum.

If sagging hinges aren't a cause, the door could be misaligned and caught or rubbing against the strike plate hole in the frame. Remove the strike plate and employ a sharp tool to increase the size of its mortise. This will permit the latch to fit properly into the hole, and prevent it from rubbing against the frame.

Find the length of the cylinder using a piece of wood or a book that can be inserted into the gap above the adjustment screw. The outer dimension is measured from the outside of the door to the center of cylinder. The inner dimension is measured from the center adjustment screw until the end cylinder.

Verify the width of the lock.

If your patio door latch is difficult to turn even after oiling and cleaning it could be because it's not aligned properly with the strike plate. Make sure that your door is in a balanced position, tilt and slide patio door repairs near me that the hinge screws are secure. In most cases, however, simply moving the strike plate downwards or upwards could fix the problem.

The latch may not engage properly if the strike of the lock is too small. In this situation, you need to widen the opening with a chisel and hammer. Then test the latch to ensure it doesn't touch the jamb frame of the door or get caught the frame.

Before you purchase a replacement lock, first determine the mortise type of lock you have. This can be done by looking at the end faceplate and observing whether it is square or round. Then, take a look at the screw holes on the current lock and note the dimensions of each one. This will help you to locate a replacement lock that is exactly the same size and will fit in the hole you have already.

You'll need to locate the mortise lock and inspect it for scratches, bends or other damage that requires to be repaired. A badly bent or damaged latch is more likely than one that has been used a lot to break. Replace the lock if you notice indications of damage.

After you've examined the lock and determined which type of replacement you'll need then it's time to begin working on the actual repair. Remove the handle and spindle from your patio door, and then insert the new one. Start by installing the interior handle. Align it with the spindle and then secure it into position using two screws or bolts. Once the handle in the interior is in, install the handle on the outside and screw it in place, too. After you've completed these steps check the handles to ensure that they can be shut and open easily and that the latch is in contact correctly with the strikeplate.

Check the Strike of the Door.

The strike plate and the door latch are two components that work together to secure the door. An incorrectly aligned strike plate and door latch will result in the latch not being able to latch the door properly. This is typically easy to repair.

Check the holes for receiving of the strike plate to ensure they are clear of obstructions, such as dirt or plastic plugs. Then loosen the screws that secure the strike plate in place and allow it to move horizontally, but not separating it from the frame of your door. Adjust the strike plate to align its receiving holes with the latch hooks of the door latch. After the strike plate has been adjusted then tighten the screws and test the door to determine if it shuts smoothly with the new adjustment.

These plates are difficult to reach for homeowners with sliding patio doors. However, they are essential for locking and unlocking your door. These metal plates are usually placed on the top and bottom of the door jamb, where they support the door's latch. The door latch slides into this strike plate and creates an airtight seal. If the strike plate is damaged, rusted, or is not installed correctly, the latch may not properly lock the door.

One of the most common reasons for an outdoor door lock to stick or not close is a misalignment of the latch and strike plate. This can be checked with the "lipstick" test. Rub some lipstick along the edge of the deadbolt, then cover it with masking tape. The lipstick will leave the mark when you close the door. This will show you exactly where the latch meets the strike plate. If the mark is too low or high you can adjust the strike plate.

If your patio door locks for sliding are not working properly they could be a problem in keeping your home safe from burglars. You must repair the issue as soon as you can. Follow these simple steps to fix your patio door lock and restore it's function.